EN50155 1000A Hall Effect Current Sensor For Converter

Datos del producto:

Pago y Envío Términos:

Cantidad de orden mínima:	100
Detalles de empaquetado:	Embalaje original
Tiempo de entrega:	1-12 semanas
Condiciones de pago:	T/T

Contacto

Descripción detallada del producto

IPN actual de medición clasificado (a):	1000	IP de la gama de medición (a):	0~±2100
Da vuelta al ratio:	1:5000	Voltaje de fuente de alimentación VC (v):	× DE DC± (15~24) (1±5%) V
Salida clasificada ISN (mA) de la medida:	200mA	Consumo actual lateral secundario IC (@±24V):	≤35mA+
El aislamiento soporta voltaje:	3.8kVrms/50Hz/1min	Δi básico del error (@IPN, TA=25℃):	el ≤±0.4%
Alta luz:	1000A Hall Effect Current Sensor , EN50155 Hall Effect Current Sensor

NT1000D-S/SP1 current sensor

Product Details

product manual

The magnetic balance Hall current sensor is suitable for accurate measurement of AC, DC and pulsating current isolation. The primary side and the secondary side are completely insulated during measurement.

product advantages	Applications	Reference standard
High precision	AC inverter AC	EN50178 EN50155
Good linearity	Battery powered
Low temperature drift	Converter/Inverter
Broadband	UPS/SVG
Quick response

Main electrical parameters
Rated measuring current IPN (A)	1000
Measuring range IP (A)	0～±2100
Turns ratio	1:5000
Power supply voltage VC (V)	DC ± (15 ~ 24) × (1 ± 5%) V
Rated measurement output ISN (mA)	200mA
Measuring resistance RM (Ω)
70℃ 85℃ @ ± 15V, ± 1000A: 0Ω ~ 23Ω 0Ω ~ 19Ω @ ± 15V, ± 1300A: 0Ω ~ 7Ω @ ± 24V, ± 1000A: 0Ω ~ 63Ω 10Ω ~ 61Ω @ ± 24V, ± 2100A: 0Ω ~ 6Ω
Secondary side current consumption IC (@±24V)	≤35mA+
Isolation withstand voltage	3.8kVrms/50Hz/1min

Accuracy-dynamic parameters
Basic error δi (@IPN,TA=25℃)	≤±0.4%
Linearity δL (@IPN,TA=25℃)	≤±0.1%
Zero output current IO (@IP=0, TA = 25℃)	≤±0.4mA
Zero temperature drift IOT	≤ ± 0.8mA (-40 ℃ ~ + 85)
Response time	≤1µS
di/dt accuracy	＞50A/us
Frequency bandwidth BW	DC..100kHz

General data
Working temperature Ta	-40℃~+85℃
Storage temperature Ts	-45℃~+90℃
Relative tracking index	＞175
weight	≤850g

EN50155 1000A Hall Effect Current Sensor For Converter 0

Mechanical characteristics
No tolerance	±1 mm
Sensor installation method one (recommended)	4 hole and 4 notch ø5.3mm 4 M5 steel screws
Sensor installation method two (recommended)	2 hole and 2 notches ø 5.3mm 2 M5 steel screws
Recommended torque	3.5 N·m
Busbar size (recommended)	40.5×13mm
Secondary side electrical connection	3 ×M4 screw

Remarks

1. When the measured current direction is consistent with the direction marked on the sensor, the sensor output ISN is positive.
2. The secondary side connection line of the product is preferably a shielded line. The shielding layer is close to the product end and the connection line can be connected to the case, and the negative power supply or power supply 0V.
3. The verticality requirements for the mounting screw holes of the power sensor: it is required to be level 8 or above (or below 0.06) in the national standard.
4. The flatness requirements for the installation surface of the power sensor:
(a). The flatness of the large plane installation is national standard 11 or above (or the flatness is less than 0.25mm);
(b). The flatness of the installation surface is designed with small round bosses It is required to reach the national standard level 12 or above (or the plane fluctuation is less than 0.5mm);
5. No tolerance ±1mm is noted;

etiqueta:

Persona de Contacto: Miss. Elaine

Teléfono: +86 18150151931

Fax: 86-592-2611505

Otros productos

Deriva de la temperatura de UPS SVG Hall Current Sensor With Low

Alta precisión: CA del inversor de la CA

Buenas linearidades: con pilas

Deriva de la baja temperatura: Convertidor/inversor

De banda ancha: UPS/SVG

Inversor 50A Hall Effect Current Transducer de la CA

IPN actual de medición clasificado (a): 50

IP de la gama de medición (a): 0~±70

Da vuelta al ratio: 1:1000

Voltaje de fuente de alimentación VC (v): +/-12V~+/-15V (+/--5%)

7kV Hall Current Sensor EN50178 con la deriva de la baja temperatura

IPN actual de medición clasificado: 1000A

Gama de medición IPM: ±2000A

Voltaje de fuente de alimentación VC: × DE DC± (15~24) (1±5%) V

Consumo actual IC (@±24V): ≤±30mA+ISN

GB/T 25119 13.4kV 2400A Hall Effect Current Transducer

IPN actual de medición clasificado: 1000A

Gama de medición IPM: ±2400A

Voltaje de fuente de alimentación VC: × DE DC± (15~24) (1±5%) V

Consumo actual IC (@±24V): ≤±30mA+ISN

1us respuesta 1000A Hall Effect Current Sensor EN50178

IPN actual de medición clasificado: 1000A

Gama de medición IPM: ±2100A

Voltaje de fuente de alimentación VC: × DE DC± (15~24) (1±10%) V

Consumo actual IC (@±24V): ≤±35mA+ISN